Product Data Sheet Show all documents

Sika FastFix®-134 TP

Bedding mortar for stone setts, concrete blocks, pavers and repair mortar for small fast repairs in concrete roads

Sika FastFix®-134 TP is a ready to use one component cementitious bedding mortar for stone setts, concrete blocks and pavers in trafficked or pedestrian areas. It can  be used for patch repairs on concrete roads.

  • Fast setting
  • Excellent adhesion to pavers, natural stone setts, concrete blocks
  • Good resistance to freeze/ thaw cycles and to de-icing salts (CDF method)
  • High mechanical properties
  • High impact resistance
  • Resistance to hydrocarbons
Product Data Sheet Show all documents

Usage

Bedding mortar for stone setts, concrete blocks and pavers for trafficking and non-trafficking areas and for small repair in concrete roads.
  • Trafficked roads
  • Pedestrian areas
  • Car parks and driveways
  • Streets
  • Gardens and landscaping
 

Advantages

  • Fast setting
  • Excellent adhesion to pavers, natural stone setts, concrete blocks
  • Good resistance to freeze/ thaw cycles and to de-icing salts (CDF method)
  • High mechanical properties
  • High impact resistance
  • Resistance to hydrocarbons

Packaging

25 kg bag

Colour

Grey powder

Product Details

Sustainability / Certifications / Approvals

CERTIFICATES AND TEST REPORTS

  • CE Marking and Declaration of Performance to EN 1504-3 - Concrete repair product for structural repair
  • Meets the requirements of ZTV-Wegebau: Category of use N1-N3
Product Information

Composition

Cement, selected aggregates and special admixtures

Shelf life

12 months from date of production

Storage conditions

Store in undamaged und unopened, original sealed packaging, in dry conditions.

Density

Fresh mortar density: ~2.3 kg/l

Maximum grain size

Dmax: 4 mm

 
Technical Information

Compressive strength

Curing Time(1)

Compressive Strength(2)

24 hours

~35 N/mm2

7 days

~76 N/mm2

28 days~99 N/mm2

(1) Curing at 20 °C and 100 % r.h.

(2) Prism 40 mm × 40mm  × 160 mm

Flexural-strength

Curing Time (1)

Flexure Strength (2)

24 hours

~6 N/mm2

7 days

~8 N/mm2

28 days~10 N/mm2

(1) Curing at 20 °C and 100 % r.h.

(2) Prism 40 mm × 40mm  × 160 mm

Tensile adhesion strength

~4 MPa

(EN 1542)

Application

Application Information

Mixing ratio

1.9 litres of water for 25 kg powder

Layer thickness

10 mm minimum / 150 mm maximum

Ambient air temperature

5 °C minimum / 35 °C maximum

Substrate temperature

5 °C minimum / 35 °C maximum

Pot Life

Temperature

Time

5 °C

> 2 hours

20 °C

~2 hours

30 °C~45 minutes

Initial set time

Temperature

Initial Set Time

5 °C

12 hours

20 °C

5 hours and 45 minutes

30 °C

4 hours

Final set time

Temperature

Final Set Time
5 °C14.5 hours
20 °C

7.5 hours

30 °C4.5 hours
Consumption

Yield

~12 litres of mortar per 25 kg bag
Application steps

MIXING

Sika FastFix®-134 TP can be mixed with a low speed (~300 rpm) hand drill mixer.

Pour the recommended water in a suitable mixing container. While stirring slowly, add the powder to the water and mix thoroughly at least for 3 minutes until a homogeneous mix is obtained.

 

APPLICATION

As a bedding mortar, pour the Sika FastFix®-134 TP and spread it with a trowel. Then, place the pre-wetted setts in the correct position by slightly pressing them in the bedding mortar.

Wait minimum 24 hours before grouting the joints with Sika® FastFix-133 TP.

A suitably qualified engineer must be responsible for the design of the expansion joints.

CURING TREATMENT

Protect against evaporation, frost and rain until the material has achieved its final setting/hardness.

CLEANING OF EQUIPMENT

Clean all tools and application equipment with water immediately after use. Hardened material can only be mechanically removed.

Documents