Sika AnchorFix®-1
Sika AnchorFix®-1 is a solvent and styrene free based, two-component polyester anchoring adhesive.
- Fast curing
- Standard guns can be used
- Can be used at low temperatures
- High load capacity
- Non-sag, even overhead
- Styrene-free
- Low odour
- Low wastage
Usage
As a fast curing anchoring adhesive for all grades of:- Rebars / reinforcing steel
- Threaded rods / bolts
- Concrete
- Hollow and solid masonry
Advantages
- Fast curing
- Standard guns can be used
- Can be used at low temperatures
- High load capacity
- Non-sag, even overhead
- Styrene-free
- Low odour
- Low wastage
Packaging
300 ml standard cartidge: 12 cartridges per box / pallet: 75 boxes
Colour
| Component A: | white |
| Component B: | black |
| Component A+B mixed: | light grey |
Product Details
CERTIFICATES AND TEST REPORTS
- Injection system for use in masonry according to ETAG 029, ETA-12/0227, Declaration of Performance 020403010010000001 5034408, certified by notified product certification body 0679, certificate of constancy of performance 0679-DPD-0777, and provided with the CE marking
- Bonded injection type anchor for non cracked concrete according to ETAG 001 annex 1 and 5, ETA-13/0720, Declaration of Performance 020403010010000001 5034408, certified by notified product certification body 1020, certificate of constancy of performance 1020-CPD-090-029816, and provided with the CE marking.
Shelf life
12 months from date of production
All Sika AnchorFix®-1 cartridges have the expiry date printed on the label.
Storage conditions
Stored properly in original, unopened, sealed and undamaged packaging in dry conditions at temperatures between +5 °C and +25 °C. Protect from direct sunlight.
Density
~1.63 kg/l (component A+B mixed)
Compressive strength
~60 N/mm2 (7 days, +20 °C) | (ASTM D 695) |
Modulus of elasticity in compression
| ~3,500 N/mm2 (7 days, +20 °C) | (ASTM D 695) |
Flexural-strength
~28 N/mm2 (7 days, +20 °C) | (ASTM D 790) |
Tensile strength
~12 N/mm2 (7 days, +20 °C) | (ASTM D 638) |
Temperature resistance
| Long term | 40 °C min. / +50 °C max. |
| Short term (1–2 hours) | +80 °C |
Application
Mixing ratio
Component A : component B = 10 : 1 by volume
Layer thickness
3 mm max.
Sag flow
Non-sag, even overhead
Material temperature
Sika AnchorFix®-1 must be at a temperature of between +5 °C and +40 °C for application.
Ambient air temperature
-10 °C min. / +40 °C max.
Dew point
Beware of condensation.
Substrate temperature during application must be at least 3 °C above dew point.
Substrate temperature
-10 °C min. / +40 °C max.
Curing time
| Temperature | Open time - Tgel | Curing time - Tcur |
| +30 °C | 4 minutes | 35 minutes |
| +25 °C – +30 °C | 4 minutes | 40 minutes |
| +20 °C – +25 °C | 5 minutes | 50 minutes |
| +10 °C – +20 °C | 6 minutes | 85 minutes |
| +5 °C – +10 °C | 10 minutes | 145 minutes |
| +5 °C | 18 minutes | 145 minutes |
| –10 °C 1 2 | 30 minutes | 24 hours |
1 Minimum cartridge temperature: +5 °C
2 This application is not covered by the scope of the product ETA or any other approval.
Consumption
Material consumption per drill hole:
Anker: Anchor
Bohrer: Drill
Bohrlochtiefe in mm: Drill hole depth in mm
The above filling volumes were calculated without waste. Consumption waste is approx. 10-50 %.
The filling quantity can be checked with the help of the scale on the cartridge.
SUBSTRATE QUALITY
- Mortar and concrete must be at the required strength. No need to be 28 days old.
- Substrate strength (concrete, masonry, natural stone) must be verified.
- Pull-out tests must be carried out if the substrate strength is unknown.
- The anchor hole must always be clean, dry, free from oil and grease etc.
- Loose particles must be removed from the holes.
- Threaded rods and rebars have to be cleaned thoroughly from any oil, grease or any other substances and particles such as dirt etc.
MIXING
Getting the cartridge ready: 300 ml / 550 ml
|
| 1. Unscrew the cap |
|
| 2. Cut the film |
|
| 3. Screw on the static mixer |
|
| 4. Place the cartridge into the gun and start application |
When the work is interrupted the static mixer can remain on the cartridge after the gun pressure has been relieved. If the resin has hardened in the nozzle when work is resumed, a new nozzle must be attached.
CLEANING OF EQUIPMENT
Clean tools and application equipment with Sika® Colma Cleaner immediately after use. Hardened / cured material can only be mechanically removed.