Sikafloor® MultiDur EB-13
Sikafloor® MultiDur EB-13 is a slip resistant, coloured, rigid flooring system based on epoxy resins conforming to OS8 German standards with improved resistance against amine blushing under critical weather conditions.
- Improved resistance against amine blushing
- Conforming the OS 8 German standards
- Good chemical and mechanical resistance
- Easy application
- Liquid proof
- Gloss finish
- Easy cleanability
Systemstruktur
Anwendung
- For concrete and cement screeds with normal up to medium heavy wear e.g. storage and assembly halls, maintenance workshops, garages and loading ramps.
- For multi-storey and underground car parks and for wet process areas, e.g. beverage and food industry
Vorteile
- Improved resistance against amine blushing
- Conforming the OS 8 German standards
- Good chemical and mechanical resistance
- Easy application
- Liquid proof
- Gloss finish
- Easy cleanability
Verpackung
Please refer to the individual Product Data SheetFarbsystem
Available in various colour shades.
Aussehen System
Slip resistant, gloss finish
Systemdetails
PRÜFZEUGNISSE
Certified as Surface Protection System OS 8 according to DIN EN 1504-2 and DIN V 18026.
Lagerfähigkeit
Please refer to the individual Product Data Sheet
Lagerbedingungen
Please refer to the individual Product Data Sheet
Systemaufbau
Sikafloor® MultiDur EB-13
| 1.Scratch coat & broadcast | Sikafloor®-156/-161/-160 & broadcast with quartz sand 0.4–0.7 mm |
| 2.Wearing coat | Sikafloor®-378 |
Chemische Basis System
Epoxy
Nenndicke System
~2.0–3.0 mm
Chemische Beständigkeit
Please refer to the chemical resistance of Sikafloor®- 378.
Thermische Beständigkeit
| Exposure* | Dry heat |
| Permanent | +50 °C |
| Short-term max. 7 d | +80 °C |
| Short-term max. 12 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Anwendung
Materialtemperatur
Please refer to the individual Product Data Sheet
Lufttemperatur
+10 °C min. / +30 °C max.
Relative Luftfeuchtigkeit
80 % r.h. max.
Taupunkt
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Untergrundtemperatur
+10 °C min. / +30 °C max.
Untergrundfeuchtigkeit
When performing application work with Sikafloor® MultiDur EB-13, the substrate moisture content must not exceed 4 % pbw measured by Tramex.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Wartezeit zwischen den Arbeitsgängen
Before applying Sikafloor®-378 on Sikafloor®-156/-161/-160 allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 24 hours | 3 days |
| +20 °C | 12 hours | 2 days |
| +30 °C | 8 hours | 1 day |
Before applying Sikafloor®-378 on Sikafloor®-378 allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 30 hours | 48 hours |
| +20 °C | 24 hours | 24 hours |
| +30 °C | 16 hours | 30 hours |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity
Wartezeit bis zur Nutzung
| Temperature | Foot traffic | Light traffic | Full cure |
| +10 °C | ~72 hours | ~6 days | ~10 days |
| +20 °C | ~24 hours | ~4 days | ~7 days |
| +30 °C | ~18 hours | ~2 days | ~5 days |
Materialverbrauch
| Coating System | Product | Consumption |
| Scratch Coat | 1 × Sikafloor®-156 /-160 filled at 1:1 with quartz sand 0.1–0.4mm or Sikafloor®-161 filled at 1:0.5 with quartz sand 0.1–0.4mm | ~1.3 kg/m² |
| Broadcast in excess | quartz sand 0.4–0.7 mm | ~4–6 kg/m² |
| Top coat | 1–2 × Sikafloor®-378 | ~0.6–0.8 kg/m² |
CLEANING
Please refer to the Method Statement Sikafloor®‐ Cleaning Regime